Tiny stepper torques big

Having calculated that the tiny stepper and GM17 gearbox combination should be able to drive a pinch wheel, I made a lash up to test the theory.

When you have a 3D printer "lash up" is probably not the right term as quite sophisticated parts can be made easily.



Here it is pulling a spring balance with a piece of HDPE filament.



It got to 10 Kg and then the coupling from the GM17 to the 4mm shaft of the pinch wheel let go.



Not surprising given the torque involved and the fact that it was made with 25% fill. I made it again with 100% fill. I can't remember the last time I made a solid part.



It is coupled to the shaft with a hexagonal steel insert drilled out to 4mm and tapped M3 for a set screw onto a flat on the shaft.



With the 100% fill coupler it easily pulled the scale to the end, i.e 12.5Kg. The motor was powered from 8V (to stop it getting too hot) and stepped at 200pps. With a step angle of 15°, the GM17 default gear ratio of 228:1 and a 13mm pinch wheel that gives a feed rate of: -

200 × 15 / 360 × 1 / 228 × 13 × π = 1.5 mm/s.

That would give an output rate of 54mm of 0.5mm filament per second. I think that is comparable to the rates Adrian Bowyer has reported from a NEMA17, but it only weighs about 60g whereas a NEMA17 is about 200g. There are a lot more parts to wear out though, so a NEMA17 may be a better option. Darwin can easily throw 200g about and HydraRaptor is moving table, so the head weight has little relevance.

I have some NEMA17's arriving this week. I tried one from an old disc drive but it didn't have much torque. I don't know if that was because it had aged in the 20+ years I have had it or whether modern motors are much better.

GM17 stepper hack

I have thought for some time that the best thing to drive an extruder with would be a small stepper with a gearbox. The reason being is that a stepper motor has close to zero efficiency when moving slowly. Power is speed multiplied by torque, so as speed increases the efficiency increases until the torque falls away due to inductance. A gearbox allows a much smaller stepper to be used because it can be run faster producing more power.

I had a look for steppers with gearboxes, but they seem to be ridiculously expensive. An alternative idea was to replace the DC motor in a gear motor with a small stepper. I couldn't find one with the correct ratio though until Solarbotics started selling replacement gears for the GM17. They allow the standard ratio of 1:228 to be changed to 1:104 or 1:51.



That makes the GM17 very flexible as they also do a magnetic shaft encoder with an integral H-bridge driver. Great for robotics, but it seems a bit under powered for an extruder.



The motor is about the same size, and has the same shaft, as the tiny steppers I got from Jameco for my first attempt at an alternative Z-axis.

I cut away the plastic cylinder that holds the motor and RepRapped an adapter flange to mount the stepper.



Here it is assembled: -


The small pinion gear is a push fit on the motor shaft, but I found that with the higher torque from the stepper I had to glue it on.

I can run the stepper up to 1000 steps / second in full step mode, with a 12V constant voltage bipolar drive. The step angle is 15° so that is 2500 RPM! It has very little torque at that speed, but it gets multiplied by the gear ratio of course.

At lower speeds the current increases and the motor gets way too hot at 12V, so it needs to be driven from a constant current drive. That is what I was intending to use anyway.

Jameco state the holding torque as 140 g.cm, so I have calculated the torque after the gearbox, assuming no losses as: -

Ratio	Max Speed	Max Torque
51	49 RPM	0.7 Nm
104	24 RPM	1.4 Nm
228	11 RPM	3.1 Nm

It seems remarkably high as NEMA23 steppers are only about 1 Nm. Note that the max speed is for about zero torque and the max torque is for about zero speed.

I attached it to a screw drive extruder and managed to extrude ABS at a rate equivalent to 0.5mm @ 19 mm/s with a step rate of 800 pps using the 1:51 gears.



So similar performance to a GM3 with these advantages: -

• No brushes to wear out.
• No shaft encoder and PID software.
• No RFI suppressor.
• Only needs step and direction pins on the controlling micro rather than two or three H-bridge controls and two quadrature inputs.
• The output shaft and final gear are one piece, whereas on the GM3 the plastic shaft is on a metal splined shaft that can slip.
• The clutch is one gear back from the output, so gives higher torque before slipping.
  

The interesting thing is that the projected torque figures indicate that it would be able to do a pinch wheel extruder with its original gear set. I will give that a go next.

I think the cost is about the same as a NEMA17. The advantage is it is smaller and lighter, the disadvantage is it would need separate bearings and a coupler. The NEMA17 will go a lot faster, but has less torque.

Dinosaur?

This may be an evolutionary dead end, with the move to stepper motors and pinch wheels, but I wanted to try a couple of things that have been on my "to try" list for a long time.

The main issue that I have had with the pump part of the original extruder is that the bearings wear out fairly quickly. Both the half bearings themselves and the lands on the shaft. One problem is that being only half bearings, any lubrication soon gets carried away by the plastic.

The best lifetime I have had is with stainless steel bearings and a stainless steel shaft. The downside of a stainless steel shaft is that you cannot solder a nut on to provide the drive. I have found two ways round this:-

1. Use a hex head bolt. For some reason stainless steel bolts never seem to have thread all the way to the top. Since the thread needs to be sharpened with a die anyway, it can be extended at the same time. It is hard work tapping stainless steel though. You need a split die, set to its biggest diameter to start with, and you need cutting compound. The hex head allows you to get a good grip to stop it turning and the original thread makes it easy to start off square.
   
2. Drill through the nut and shaft and insert a pin. If, like me, you break lots of drills then broken drill shafts make perfect pins. I now buy drill bits in packs of five or ten!

I replaced the two half bearings with three ball bearings. At the top is an M5 bearing to take the axial thrust. At the bottom I use two M4 bearings as rollers to take the radial load.



The downside of this arrangement is that you still need to turn a land on the bottom of the shaft. It could probably be done with a file and drill though. It actually works without removing the thread, but I expect it might wear away the rollers.

This design works but there are a few things I would change if I built another: -

I made it compatible with the existing filament guide to avoid having to reconfigure my machine for HDPE. Ideally the screw holes at the bottom end need to move out to allow longer bolts to hold the rollers and the size needs increasing from M3 as the threads strip eventually.

I left clearance to allow the top bearing to be inserted from below, but left no access to the nuts. Consequently it was very difficult to assemble and I had to make undersized nuts.

I used the smallest outside diameter bearings I could find for the given inside diameter. That was a mistake because it is hard not to foul the outer part of the bearing with a washer as the moving part is so small. Star washers seem to just grip the inner and provide enough standoff to clear the outer. I used counter sunk heads to clear the outer face of the rollers. I expect larger diameter bearings use bigger balls, so perhaps have higher ratings.

All easy things to put right with a design iteration.

Another thing I have been meaning to try is the GM17 gearmotor. I have had some for a long time, but without a second shaft, adding a shaft encoder is not trivial, as it is with the GM3. Solarbotics now sell a cheap magnetic encoder that fits inside the casing, making it a more attractive proposition.

To fit the motor in place of the GM3 a new mounting bracket and a shorter version of the shaft coupler is needed.



Here is the completed pump: -



And here it is built up into an extruder: -



I am waiting for the magnetic encoder to come from Canada so I tested it open loop with a couple of bench power supplies.

The GM17 is a bit quieter than the GM3, but not that much when heavily loaded. It extrudes at a similar rate, but the speed seems to vary a lot with load, so it would be useless without closed loop control. It seems to labour and get quite hot at 12V, so I don't imagine its life would be a lot better than GM3. It overruns a lot when the power is disconnected, so it would need a full H-bridge and reverse thrust to get decent stopping.

I still have lots of things to try: stepper drive, a roller instead of the filament guide, an offset screw drive to avoid the rollers.